How To: Make a Spot Welder for Cheap!
A typical resistance spot welder can range in price from about $200-$800, but with a little resourcefulness and a bit of free time, you can make one like this for about $10 or less.Before starting on this project, there are a couple of videos you should check out, because you may want some background on how the device works. Firstly, check out how to make the Metal Melter, then see what it can do. Please enable JavaScript to watch this video.
Spot welders are used to fuse thin sheets of metal together. They are most likely used in the auto industry, as well as HVAC for welding metal duct. Measuring the base of my Metal Melter, I found it was about 4-1/4".I found a 6' length of 1x6 common board for about $4, which actually measures out at 5-1/2", so it will work just fine.Two pieces of the board will need to be cut to 12" lengths (5-1/2" x 12"), but the rest can be pushed through a table saw to trim the width down to 4-1/2" (1/4" wider than the transformer base). The piece of common board that you just trimmed down to 4-1/2" wide can be cut into 3 pieces measuring:4" x 4-1/2" 12" x 4-1/2" 24" x 4-1/2" The other 2 pieces of the common board should measure:12" x 5-1/2" (x 2 pieces) You'll also need 4 pieces of 2x2 measuring;2" x 2" x 13-1/2" (x 2 pieces) 2" x 2" x 4" (x 2 pieces) This is all of the wood you'll need for building the casing. I used a 3/4" rounding bit and my router to smooth the edges and give it a cleaner look. This is roughly how it will look when it's assembled. Image via wonderhowto.com A notch needs to be cut on one of the 2x2 arms, and you'll see what this is for later on. I found a piece of scrap can be used as a template. The notch can be cut out with a bandsaw, wood saw, or any other saw you can get creative with. I used a jig-saw, but wouldn't recommend it as the safest option.The back panel (4" x 4-1/2") also gets holes cut that will accommodate an electrical light switch, and a notch for a power cable. The pieces get sanded, primed, and painted. I chose to paint this black and yellow.When I salvaged the Microwave Oven Transformer in this previous project, I saved some of the other components that can be used for our Spot Welder:The power cord The door handle Wires for the transformer terminals, with insulated spade connectors Power switch, with wires and insulated spade connectors Aside from these, the only other items you'll need are:Simple light switch, with faceplate Copper offset terminal lugs that will hold (x 2) 1/4" hex screws (x 2) Small nails (x 2) Length of solid copper wire (4AWG is better, but I used 6AWG in this project) The solid copper wire can be snipped into 1" lengths, that fit nicely into the terminal lugs. The lugs have a mechanism that can be tightened with a screwdriver to secure the connection with the wire. The tighter the better.Now that the wood is painted, finished, and dry (I gave it about 2 days), the unit can be assembled.The back panel is for a light switch and a power cord.Before screwing the panel into the base, make sure your cord goes in first. The thick piece at the end of the cord prevents it from pulling back though the hole. This is also the time to add the 2 pieces of 2" x 2" x 4" support blocks to the base. Be sure of your measurements before you screw them down. You want them to end up flush with the side panels when it's done.The Metal Melter can be placed inside now, and when a good position is found, can be screwed to the base with a couple of small screws.Now it's time to wire up the electrical system.Starting with the power cord coming into the casing, I stripped the black wire, and attached it to the bottom terminal of the light switch. Image via wonderhowto.com Next, I attached one of the wires I had salvaged, to the right terminal on the transformer. Image via wonderhowto.com Then stripped the other end, and attached that to the top of the light switch. Image via wonderhowto.com The electrical could almost be finished here, but I wanted to add another switch, for safety and convenience, and that's where the salvaged switch from the microwave hack comes in. Image via wonderhowto.com The two wires attached to the switch can be wrapped with electrical tape to secure the connection and help insulate from electric shock.The both ends of the wires are stripped so the copper wire is exposed.One wire connects to the left terminal of the Metal Melter's primary coil, and the other wire connects to the white wire on the power cable that runs back to the house. Image via wonderhowto.com The electrical system is complete! The sides can be screwed on with 6 wood screws on each side. I used 2" wood screws after drilling pilot holes to make sure the wood didn't split.The trigger switch is attached near the tip of the top welder arm, and at a bit of an angle so it can be pressed easily. I found that 2 small nails held this in place perfectly.Both arms can get inserted into the front of the casing, and with a bit of guesswork, a hole can be drilled through the side of the casing and into the end of the arms, so that when a nail is inserted, it will pivot.Now you can see why we needed the notch in the arm. To help the arm stay in an upright position, I added a couple of screws and rubber bands to keep the tension. This also provides a little back pressure, and stabilization when using the welder.The copper lugs can be added to the tips of the arms.I drilled pilot holes with a 3/16th drill bit, then secured the lugs by pushing the hex bolts first through the hole in the lugs, then through the lugs on the the Metal Melter terminals.One in the top, and one in the bottom. It shouldn't matter which way they go, but I chose to make my top cable on the same side as the switch because it was easier to handle.If the electrode tips don't line up perfectly, it's easy to bend them a little until they do. When finished, it should look like this. It will only work if the safety switch on the back is turned on, and even then, no power is delivered until the thumb operated switch is pressed.To use, place thin sheets of metal between the electrode tips, then press the button with your thumb for about 3-4 seconds. The massive electrical current pushing through the metal, heats it up to the point where it fuses with the other sheet. You can release your thumb from the switch and wait until the weld cools enough to handle.Welding these metal washers worked so well, I couldn't break them by hand. I had to use 2 pairs of pliers to get them to snap. Images via wonderhowto.com When the energized electrode tips touch each-other, you can see the high-amp sparks. Image via wonderhowto.com Note: Burning galvanized metals may release zinc-oxide fumes. Welding should be done in a well ventilated area.The electrode arms are only held in with nails, so if the nails are removed, the arms can be removed to extend the welders reach, and access difficult angles.They go back together very easily, and the elastic can be conveniently replaced when necessary. Image via wonderhowto.com When the electrode tips are spent, it's easy to unscrew the bolt holding them in place, and add a fresh piece of copper wire. Copper wire is relatively cheap. You can get a pice of 12" 4AWG wire for about a dollar. That means each tip is less than 10 cents each!The power of the metal melter is still evident in the way this can bring iron metal to a boil! Be careful running the welder too long because there is a chance the wires will get so hot that the insulation on the cables will start smoking and melt. Now you know how to make my version of a cheap Spot Welder.If you haven't seen the step-by-step video, you can still see it here.If you like this project, perhaps you'll like some of my others. Check them out at www.thekingofrandom.com.
How To: Keep Photos from Hogging Your iPhone's Storage
Email is one of the least private and least secure forms of communication, although few people realize this. MixMaster is one way to allow secure, anonymous communication even over the very public medium of email.
Anonymize Your Emails with MixMaster - YouTube
This video demonstrates how to upload Moodle to your server via the Webmin interface. This video demonstrates how to upload Moodle to your server via the Webmin interface. Using Lessons in
How to Install Moodle on your server with a web browser
Are you tired of uploading videos to different sites separately? It's really time consuming and difficult. Finally, there is a way to upload and distribute your videos to YouTube, Facebook, Dailymotion, and many more video-hosting websites in one go. No need to upload to every site separately and one by one.
How to Upload Video to Multiple Sites At Once | TechUntold
Last year's Asus Zenfone 5Z was an excellent phone with great hardware and an even better price point. The Zenfone 6, however, takes everything its by Jordan Palmer in ASUS, News, Phone Reviews
ZenFone 5Z (ZS620KL) | Phones | ASUS USA
The shortcut actually uses your Reminders app to work its magic, so if you haven't already given Shortcuts access to Reminders, you'll be prompted to do so now. Now, if you typed in 5 minutes, you will get a notification from Reminders in roughly five minutes which reads, "[Task name] timer finished!"
Google Home Now Allows You to Create Voice-Activated
All it takes to keep your earbuds, USB cables, power cords, etc. tangle-free is to tie them up the right way. First, you're going to take the bigger end of your cable (the headphones, in this case), and pinch them between three fingers and your thumb.
6 DIY Ideas for Keeping Your Earbuds Tangle-Free « The Secret
Play Ultimate Cribbage, the classic card & board game that friends & family have been enjoying for decades! If you already play Canasta, Pinochle, Backgammon, Gin Rummy 500, or Solitaire, then you'll love this classic card & board game.
How to Play Retro Video Games | PCMag.com
Here's how to use the Edge screen on Galaxy S7 Edge. While the Edge Panel is the most obvious feature of Samsung's Edge screen-optimized software, the curved secondary screens do have
How to make the most of your trip to Star Wars: Galaxy's Edge
How To: Download music from MySpace as an MP3 How To: Save music from MySpace or any other website How To: Save music from MySpace and covnert it to an MP3 How To: Save music from MySpace to your computer easily How To: Find free Mp3s on the Internet
How to Download Music from MySpace in 2018 - easeus.com
Google Earth is the most photorealistic, digital version of our planet. Where do the images come from? How are they they put together? And how often are they updated?
Galaxy Oreo Update: Samsung Adds Screenshot Labeling Feature in Android 8.0 News: The Differences Between the Galaxy S8 & Galaxy Note 8 Oreo Updates How To: Here's How Your Apps Will Get Better Now That They Have to Target Oreo News: Essential Releases Oreo Beta 2 Update
Samsung Galaxy S7s Overheating Because of Oculus App Update
Sempre que você quiser conferir a nova interface do Netflix, basta ir até Apps no painel do Xbox e clicar no Netflix. Você também pode usar o Quickplay no painel. Mas a única maneira de visitar a versão antiga do Netflix é indo ao Guia Xbox, Jogos, Quickplay, na guia Todos e clicando na versão "filmstrip".
Kembalikan ke Aplikasi Netflix Lama di Pembaruan Xbox 360
How to Adjust Colors on an LCD Monitor. When viewing images on an LCD (Liquid Crystal Display) monitor, the images should be crisp and clear and the colors should be rich and vibrant. Typically, setting the LCD monitor colors to its native
LG Video Tutorials: Adjusting Picture Settings - webOS 2.0
This video demonstrates how to power on a Samsung phone without using the power button. How to Power On / Turn on ANY Samsung Phone Without The Power Button FAKE Galaxy S9+ vs. REAL
Galaxy S8 battery drains quicker after an update
0 comments:
Post a Comment